Fault code P06A9 – sensor reference voltage “D” circuit range/performance

Fault code P06A9 is called “Sensor Reference Voltage “D” Circuit Range/Performance” but in different programs it may be called differently. This fault designation applies to all vehicles equipped with OBD-II.

Technical description and explained code P06A9

Stored code P06A9 means that the Powertrain Control Module (PCM) has detected a non-conformance in the operating range of the sensor reference voltage in the “D” circuit. In this case, it is not a specific sensor, but any of the sensors in the “D” circuit.

Fault code P06A9 – sensor reference voltage

Usually this circuit is powered by the throttle position sensor (TPS) and accelerator pedal position sensor #1 (APPS). But sometimes others may be present, depending on make and model.

All of these sensors have a 5V reference voltage on the same circuit as the PCM, and a signal is received. If the input voltage signal received by the PCM is outside the expected parameters, code P06A9 will be stored.

Thus, if a mismatch occurs in the “D” voltage reference circuit, all sensors that share this circuit may be affected. But in many cases this error will be accompanied by other codes. Which will help narrow down the general area in which this fault is present.

Regardless of whether or not other codes are present, this error means that a performance range mismatch has been detected in the “D” reference voltage circuit.

Symptoms of vehicle malfunctions

The main signal that an error P06A9 has occurred is the Malfunction Indicator Lamp (MIL) is also known as the CheckEngine Light.

It can also be warning signs such as:

  1. The “Check engine” control lamp on the control panel will light up (the code will be recorded in the memory as a fault).
  2. Additionally, there may be codes indicating a problem with a particular sensor.
  3. Poor acceleration.
  4. The engine cannot be accelerated, the throttle response is unresponsive.
  5. Increased fuel consumption.
  6. Decrease of the engine power.
  7. Floating revolutions, as well as attempts to stall at idle.

The severity of the stored fault code P06A9 depends on which of the circuit sensors the breakage occurred in. Therefore, the degree of criticality will be different in each case.

Factors that can cause this error code

The error code P06A9 can mean that one or more of the following problems have occurred:

  • Throttle position sensor (TPS) is defective.
  • Accelerator pedal position sensor No. 1 (APPS) is defective.
  • Problem with connection wires or connector as melted or broken.
  • Blown fuse or fusible link.
  • Faulty system power relay.
  • Sometimes faulty PCM module is the cause.

How to fix or reset OBD-2 code P06A9

Some suggested steps for troubleshooting and fix the error code P06A9:

  1. First, connect an OBD-II scanner to the vehicle’s onboard computer and read all stored data and error codes.
  2. Then clear the error codes from the PCM memory and test-drive the vehicle to see if error P06A9 appears again.
  3. If the error code appears again, check the wires and connectors.
  4. Test the sensors in the “D” reference circuit, replace if necessary.
  5. Check control module (PCM), replace or reprogram if necessary.

Diagnose and repair of problems

Connect the scan tool to the vehicle’s diagnostic port and retrieve all stored codes. Then clear them and test-drive the vehicle. If code P06A9 does not appear, then the error was temporary. If it appears, continue testing.

Perform a visual inspection of the wiring and connectors associated with the “D” reference circuit sensors. Replace damaged wiring or connectors if damage is detected. After that, reset the errors again, test drive and read them again.

Check the sensors

If code P06A9 reappears, refer to the manual to determine which sensors are serviced by the “D” voltage reference circuit. Since manufacturers do not always adhere to part, circuit, and sensor labeling conventions.

Check the resistance, reference voltage, continuity, and grounding continuity for all relevant sensor wiring. Compare all data obtained with the values given in the manual.

Test the operation of each sensor using an oscilloscope, a library of waveforms will be required. If such equipment and reference data are not available, continuing with the diagnostic procedure is not recommended.

Improper testing procedures can cause serious damage to the electrical system and to one or more control modules.

On which vehicles does this problem occur most frequently

Fault code P06A9 can occur on different vehicles but there are statistics on which brands this occurs most often. Here is a list of some of them:

  • Chevrolet
  • Ford
  • Honda
  • Mercedes-Benz

Fault code P06A9 can sometimes be found with other errors. The most common are the following: P06A3, P06A4, P06A5.

Video

Rate article
AutoNevod | Technical description of OBD-2 car faults and their solution
Add a comment