Fault code P076A – shift solenoid “H” malfunction

Fault code P076A is called “Shift Solenoid “H” Malfunction” but in different programs it may be called differently. This fault designation applies to all vehicles equipped with OBD-II.

Technical description and explained code P076A

This diagnostic trouble code (DTC) is a generic transmission code. Error P076A is considered a general code because it applies to all makes and models of vehicles. Although the specific repair steps may vary slightly depending on the model.

Fault code P076A – shift solenoid

OBD-II trouble code P076A is set when the control module (PCM) has detected a problem in the shift solenoid valve “H” circuit. Most automatic transmissions have at least three valves which are labeled A, B and C.

The code set is based on a specific fault that alerts the PCM and turns on the check engine light.

The shift solenoid valve circuit is designed to control the operation of the shift solenoids. To control fluid movement between the various hydraulic circuits and change the transmission ratio at the appropriate time.

This process maximizes engine performance levels at the lowest possible rpm. Transmission solenoids are responsible for opening or closing valves, allowing transmission fluid to flow to the clutches. For smooth transmission shifting when the engine accelerates.

When the powertrain control module (PCM) detects a fault in the “H” shift solenoid valve circuit. Fault code P076A will be written to memory and an error message will appear on the control panel.

Symptoms of vehicle malfunctions

The main signal that an error P076A has occurred is the Malfunction Indicator Lamp (MIL) is also known as the CheckEngine Light.

It can also be warning signs such as:

  1. The “Check engine” control lamp on the control panel will light up (the code will be recorded in the memory as a fault).
  2. The vehicle goes into emergency mode.
  3. The transmission slips when shifting gears.
  4. Transmission is stuck in gear.
  5. Shifting gears is hard.
  6. Transmission overheating.
  7. Increased fuel consumption.
  8. Possible symptoms similar to ignition failure.

Depending on the symptoms, the error P076A may be moderate or serious. If there are problems with gear shifting, it is recommended to troubleshoot the problem as soon as possible.

Factors that can cause this error code

The error code P076A can mean that one or more of the following problems have occurred:

  • The “H” shift solenoid valve is defective.
  • Contaminated fluid or clogged transmission filter.
  • Low transmission fluid level.
  • Transmission fluid passages are clogged.
  • Faulty transmission pump or transmission valve housing.
  • Other mechanical problems inside the transmission.
  • A wiring problem or damaged connector.
  • In rare cases, malfunction of PCM or TCM.

How to fix or reset OBD-2 code P076A

Some suggested steps for troubleshooting and fix the error code P076A:

  1. Replace the ATF fluid and filters.
  2. Fill the transmission fluid to the required level.
  3. Flush to clean the internal passages of the transmission.
  4. Test and replace faulty shift solenoid “H” valve if necessary.
  5. Repair or replace the defective transmission pump as well as the transmission valve housing.
  6. Check the connectors as well as the wiring.
  7. Flash or replace PCM or TCM.

Diagnose and repair of problems

Before you begin the process of troubleshooting P076A, you should research the Technical Service Bulletins (TSBs) for your particular vehicle. In some cases, this can save you a lot of time by pointing you in the right direction.

Next, you should check the fluid level and check for contamination. Before replacing the fluid, you should check the vehicle’s records to see when the filter and fluid were last changed.

After that, you should do a detailed visual inspection and also check the condition of the wiring for obvious defects. Check the connectors and wiring going to the shift solenoid valve, transmission pump and PCM. Depending on the configuration, the transmission pump may be electrically or mechanically driven.

Normal readings for wiring and connections should be 0 ohms of resistance. Wiring continuity checks should always be performed with power disconnected from the circuit. To avoid short-circuiting and creating additional damage.

Resistance or lack of continuity indicates faulty wiring that is open or shorted. In this case, repair or replacement will be required.

On which vehicles does this problem occur most frequently

Fault code P076A can occur on different vehicles but there are statistics on which brands this occurs most often. Here is a list of some of them:

  • Chrysler (Pacifica, Town and Country)
  • Dodge (Grand Caravan, Journey, RAM)
  • Ford
  • Honda
  • Hyundai
  • Kia
  • Lexus
  • Mazda
  • Toyota
  • Volkswagen

Fault code P076A can sometimes be found with other errors. The most common are the following: P076B, P076C, P076D, P076E.


Rate article
AutoNevod | Technical description of OBD-2 car faults and their solution
Add a comment