Fault code P2058 – reductant injection valve circuit high (Bank 2, Unit 2)

Fault code P2058 is called “Reductant Injection Valve Circuit High (Bank 2, Unit 2)” but in different programs it may be called differently. This fault designation applies to all vehicles equipped with OBD-II.

Technical description and explained code P2058

Stored code P2058 means that the Powertrain Control Module (PCM) has detected a high signal level in the Restorer Injection Nozzle Circuit (Bank 2, Unit 2). Bank 2 refers to an engine group that does not contain cylinder number one. Unit 2 indicates that multiple injector reducer systems or SCR systems may be in use.

Fault code P2058 – reductant injection valve circuit high (Bank 2, Unit 2)

Exhaust gas recirculation (EGR) systems are designed to reduce NOx in exhaust gases. But today’s high-powered diesel engines cannot meet strict emissions standards with EGR alone.

Therefore, particulate filters, catalytic converters and NOx traps are also used to deactivate pollutants. Selective catalytic reduction (SCR) systems were invented for this reason.

SCR systems inject a reducing compound into the exhaust before the particulate filter or catalytic converter. Precisely timed injection increases the temperature of the filter element and allows it to work more efficiently.

This makes the filter element last longer and allows less harmful exhaust gases to be released into the atmosphere.

The entire SCS system is monitored and controlled either by the PCM or by a separate controller that communicates with the PCM. The controller monitors the O₂, NOx, and exhaust temperature sensors to determine the appropriate time for reducing agent injection.

The reducing agent feed pump is used to pressurize the DEF system when necessary. The PCM monitors the supply pump voltage for constant fluctuations and load percentage.

If the PCM detects a high voltage level in the restorer injector circuit (Bank 2, Unit 2) that is out of tolerance, code P2058 will be stored. The Malfunction Indicator Light (MIL) may also illuminate.

Symptoms of vehicle malfunctions

The main signal that an error P2058 has occurred is the Malfunction Indicator Lamp (MIL) is also known as the CheckEngine Light.

It can also be warning signs such as:

  1. The “Check engine” control lamp on the control panel will light up (the code will be stored as a fault).
  2. Other related fault codes may also be present.
  3. Reduced engine power.
  4. Black smoke coming out of the exhaust pipe.
  5. Increased fuel consumption.
  6. The engine will go into emergency operation mode.

Stored fault code P2058 should be considered serious and corrected as soon as possible. The SCR system may be disabled, causing damage to the particulate filter and catalytic converter.

Factors that can cause this error code

The error code P2058 can mean that one or more of the following problems have occurred:

  • The reducer injection nozzle is defective.
  • Open or short circuit in the restorer injection nozzle circuit.
  • Insufficient amount of reducing fluid in the reservoir.
  • Problem with the restorer control module.
  • Bad electrical connection in the restorer control module circuit.
  • In rare cases, PCM failure or programming error.

How to fix or reset OBD-2 code P2058

Some suggested steps for troubleshooting and fix the error code P2058:

  1. Read all stored data and error codes with an OBD-II scan tool. To find out when and under what circumstances error P2058 appeared.
  2. Clear the error codes from the computer memory and test-drive the vehicle to find out if the fault appears again.
  3. If the error code appears again, visually inspect the electrical wires and connectors.
  4. Visually inspect and test the recovery injector nozzle.
  5. If necessary, replace the restorer injection nozzle and any defective wires.
  6. Check the reducing fluid in the reservoir.
  7. Check the restorer control module.
  8. If there are no defects, check the PCM module and its software part.

Diagnose and repair of problems

Before you begin the process of troubleshooting P2058, you should research the technical service bulletins (TSBs) for your particular vehicle. In some cases, this can save you a lot of time by pointing you in the right direction.

The diagnosis itself should begin with a visual inspection of the restorer system harnesses and connectors. Burned or damaged wiring and connectors should be repaired or replaced before proceeding with testing.

Using a multimeter, test the power supply to the SCR control system. Check the fuses when the circuit is loaded to avoid misdiagnosis.

Use a multimeter to test the recovery injector injector according to the manufacturer’s specifications. Components that do not test within the maximum allowable parameters should be considered defective.

If the Restorer Injection Nozzle is within specifications, code P2058 is retained and the sensor in question is in working order. Use a multimeter to check the input and output circuits between the recovery injector and the PCM / SCR controller.

Restorer Injection Injector codes are usually associated with a faulty or disconnected injector.

On which vehicles does this problem occur most frequently

Fault code P2058 can occur on different vehicles but there are statistics on which brands this occurs most often. Here is a list of some of them:

  • Dodge (RAM)
  • Ford
  • Mercedes-Benz (C180, Sprinter, W203, W211)

Fault code P2058 can sometimes be found with other errors. The most common are the following: P2053, P2054, P2055, P2056, P2057.


Rate article
AutoNevod | Technical description of OBD-2 car faults and their solution
Add a comment